Klark Teknik SQ1S - aktywny spliter/skrzynia reporterska
To ogłoszenie jest nieaktualne
Opis produktu:
Klark Teknik SQ1S - aktywny spliter/skrzynia reporterska
Klark Teknik Square ONE splitter SQ1S
8-input / 3-output active signal splitter.
| Inputs | 8 (mic/line) |
|---|---|
| Type | Analogue, electronically balanced, female XLRs (Pin 2 hot) |
| Maximum input level | +22dBu |
| Input impedance | 5k ohms |
| Common mode rejection | -80dB at 1kHz (typical), unity gain (0dB) |
| ratio (CMRR) | -100dB at 1kHz (typical), maximum gain (+40dB) |
| Outputs | 16 (rear panel) |
| Type | Analogue, electronically balanced, male XLRs (Pin 2 hot) |
| Operating level | 0dB |
| Maximum level | +22dBu |
| Output impedance | <50 ohms |
| Signal drive capacity | <600 ohms |
| 8 (front panel) | |
| Type | Analogue, transformer isolated balanced, male XLRs (Pin 2 hot) |
| Operating level | -6dB |
| Maximum level | +22dBu |
| Output impedance | <75 ohms |
| Signal drive capacity | <600 ohms |
| Headphone output | 1 |
| Type | Analogue, TRS jack socket |
| Rating | 750mW (nominal 50 ohm load) |
| Terminations | |
| Audio | Front panel connectors |
| Channel input | eight x AA series female XLRs (labelled "IN 1" to "IN 8") |
| Isolated output C | eight x AA series male XLRs (labelled "TX OUT 1" to "TX OUT 8") |
| Headphone output | one 1/4" TRS balanced jack socket |
| Rear panel connectors | |
| Channel input | eight x AA series female XLRs (labelled "IN 1" to "IN 8") |
| Electronic output A | eight x AA series male XLRs (labelled "OUT A") |
| Electronic output B | eight x AA series male XLRs (labelled "OUT B") |
| Power | 3-pin IEC |
| Performance | |
| Frequency response1 | ±0.5dB (input to output), 20Hz to 20kHz |
| Distortion | <0.02% @ 1kHz, 0dBu at unity gain |
| Dynamic range2 | Electronically balanced outputs: >122dB* |
| Transformer isolated outputs: >140dB* | |
| Noise floor3 | Unity gain <-100dBu* |
| Mic EIN @ +40dB gain <-128dBu* | |
| High pass filter | |
| Filter frequency | -3dB @ 30Hz |
| Filter slope | 12dB per octave |
| Power Requirements | |
| Voltage | 100VAC to 240VAC ±10% |
| Frequency | 50Hz to 60Hz |
| Consumption | <35W |
| Dimensions | |
| Height | 88 mm (3.5"), 2U high |
| Width | 482 mm (19") |
| Depth | 200 mm (7 7/8") |
| Weight | |
| Net | 4.5 kg |
| Shipping | 5.7 kg |
1 Measurement conditions: unit powered, all filters bypassed, unity gain and output terminated with 20k ohm balanced loads.
2 Measurement conditions: unit powered, both inputs terminated with 150 ohms, all filters bypassed, unity gain set to 0dB and outputs terminated with 20k ohms balanced loads.
3 Measurement conditions: unit powered, all inputs terminated with 150 ohms, all filters bypassed, outputs terminated with 20k ohms balanced loads.
* 22Hz to 22kHz un-weighted.